当前位置:主页   - 电脑 - 认证考试 - Cisco
VLAN实验举例
来源:linux宝库,设计前沿收集   作者:未知   更新时间:2008-11-26
收藏此页】    【字号    】    【打印】    【关闭
  例一:
  设备选用Catalyst5500交换机1台,安装WS-X5530-E3管理引擎,多块WS-X5225R及WS-X5302路由交换模块,WS-X5302被直接插入交换机,通过二个通道与系统背板上的VLAN 相连,从用户角度看认为它是1个1接口的模块,此接口支持ISL。在交换机内划有3个虚拟网,分别名为default、qbw、rgw,通过WS-X5302实现虚拟网间路由。
  以下加重下横线部分,如set system name 5500C为需设置的命令。
  设置如下:
  Catalyst 5500配置:
  begin
  set password $1$FMFQ$HfZR5DUszVHIRhrz4h6V70
  set enablepass $1$FMFQ$HfZR5DUszVHIRhrz4h6V70
  set prompt Console>
  set length 24 default
  set logout 20
  set banner motd ^C^C
  !
  #system
  set system baud 9600
  set system modem disable
  set system name 5500C
  set system location
  set system contact
  !
  #ip
  set interface sc0 1 10.230.4.240 255.255.255.0 10.230.4.255
  set interface sc0 up
  set interface sl0 0.0.0.0 0.0.0.0
  set interface sl0 up
  set arp agingtime 1200
  set ip redirect enable
  set ip unreachable enable
  set ip fragmentation enable
  set ip route 0.0.0.0 10.230.4.15 1
  set ip alias default 0.0.0.0
  !
  #Command alias
  !
  #vtp
  set vtp domain hne
  set vtp mode server
  set vtp v2 disable
  set vtp pruning disable
  set vtp pruneeligible 2-1000
  clear vtp pruneeligible 1001-1005
  set vlan 1 name default type ethernet mtu 1500 said 100001 state active
  set vlan 777 name rgw type ethernet mtu 1500 said 100777 state active
  set vlan 888 name qbw type ethernet mtu 1500 said 100888 state active
  set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 state active
  set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101004 state active bridge 0x0 stp ieee
  set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 state active bridge 0x0 stp ibm
  set vlan 1003 name token-ring-default type trcrf mtu 1500 said 101003 state active parent 0 ring 0x0 mode srb aremaxhop 7 stemaxhop 7
  !
  #set boot command
  set boot config-register 0x102
  set boot system flash bootflash:cat5000-sup3.4-3-1a.bin
  !
  #module 1 : 2-port 1000BaseLX Supervisor
  set module name 1
  set vlan 1 1/1-2
  set port enable 1/1-2
  !
  #module 2 : empty
  !
  #module 3 : 24-port 10/100BaseTX Ethernet
  set module name 3
  set module enable 3
  set vlan 1 3/1-22
  set vlan 777 3/23
  set vlan 888 3/24
  set trunk 3/1 on isl 1-1005
  #module 4 empty
  !
  #module 5 empty
  !
  #module 6 : 1-port Route Switch
  set module name 6
  set port level 6/1 normal
  set port trap 6/1 disable
  set port name 6/1
  set cdp enable 6/1
  set cdp interval 6/1 60
  set trunk 6/1 on isl 1-1005
  !
  #module 7 : 24-port 10/100BaseTX Ethernet
  set module name 7
  set module enable 7
  set vlan 1 7/1-22
  set vlan 888 7/23-24
  set trunk 7/1 on isl 1-1005
  set trunk 7/2 on isl 1-1005
  !
  #module 8 empty
  !
  #module 9 empty
  !
  #module 10 : 12-port 100BaseFX MM Ethernet
  set module name 10
  set module enable 10
  set vlan 1 10/1-12
  set port channel 10/1-4 off
  set port channel 10/5-8 off
  set port channel 10/9-12 off
  set port channel 10/1-2 on
  set port channel 10/3-4 on
  set port channel 10/5-6 on
  set port channel 10/7-8 on
  set port channel 10/9-10 on
  set port channel 10/11-12 on
  #module 11 empty
  !
  #module 12 empty
  !
  #module 13 empty
  !
  #switch port analyzer
  !set span 1 1/1 both inpkts disable
  set span disable
  !
  #cam
  set cam agingtime 1-2,777,888,1003,1005 300
  end
  5500C> (enable)
  WS-X5302路由模块设置:
  Router#wri t
  Building configuration...
  Current configuration:
  !
  version 11.2
  no service password-encryption
  no service udp-small-servers
  no service tcp-small-servers
  !
  hostname Router
  !
  enable secret 5 $1$w1kK$AJK69fGOD7BqKhKcSNBf6.
  !
  ip subnet-zero
  !
  interface Vlan1
  ip address 10.230.2.56 255.255.255.0
  !
  interface Vlan777
  ip address 10.230.3.56 255.255.255.0
  !
  interface Vlan888
  ip address 10.230.4.56 255.255.255.0
  !
  no ip classless
  !
  line con 0
  line aux 0
  line vty 0 4
  password router
  login
  !
  end
  Router#
  
  
  3.1. 例二:
  交换设备仍选用Catalyst5500交换机1台,安装WS-X5530-E3管理引擎,多块WS-X5225R在交换机内划有3个虚拟网,分别名为default、qbw、rgw,通过Cisco3640路由器实现虚拟网间路由。交换机设置与例一类似。
  路由器Cisco3640,配有一块NM-1FE-TX模块,此模块带有一个快速以太网接口可以支持ISL。Cisco3640快速以太网接口与交换机上的某一支持ISL的端口实现连接,如交换机第3槽第1个接口(3/1口)。
  Router#wri t
  Building configuration...
  Current configuration:
  !
  version 11.2
  no service password-encryption
  no service udp-small-servers
  no service tcp-small-servers
  !
  hostname Router
  !
  enable secret 5 $1$w1kK$AJK69fGOD7BqKhKcSNBf6.
  !
  ip subnet-zero
  !
  interface FastEthernet1/0
  !
  interface FastEthernet1/0.1
  encapsulation isl 1
  ip address 10.230.2.56 255.255.255.0
  !
  interface FastEthernet1/0.2
  encapsulation isl 777
  ip address 10.230.3.56 255.255.255.0
  !
  interface FastEthernet1/0.3
  encapsulation isl 888
  ip address 10.230.4.56 255.255.255.0
  !
  no ip classless
  !
  line con 0
  line aux 0
  line vty 0 4
  password router
  login
  !
  end
  Router#
  
  
其它资源
来源声明

版权与免责声明
1、本站所发布的文章仅供技术交流参考,本站不主张将其做为决策的依据,浏览者可自愿选择采信与否,本站不对因采信这些信息所产生的任何问题负责。
2、本站部分文章来源于网络,其版权为原权利人所有。由于来源之故,有的文章未能获得作者姓名,署“未知”或“佚名”。对于这些文章,有知悉作者姓名的请告知本站,以便及时署名。如果作者要求删除,我们将予以删除。除此之外本站不再承担其它责任。
3、本站部分文章来源于本站原创,本站拥有所有权利。
4、如对本站发布的信息有异议,请联系我们,经本站确认后,将在三个工作日内做出修改或删除处理。
请参阅权责声明